Chem-Tainer Industries Septic Systems and Plastic Tanks
The Only IAPMO Listed Polyethylene
Septic Tanks Manufactured in Hawaii
Visit our website www.chemtainerofhawaii.com
 View our Open Top Plastic Tanks View Our Water and Septic Tanks View our Plastic Storage Tanks View our Spill Containment Solutions View our Septic Tanks View our Accessories and Tank Fittings
Customer Service | Products | What's New | Engineering Data | Tank Drawings | Site Map
 

 
Dealers
Subsidiaries
Customer Service
 
Rotomolding Employment
 
Open Top Tanks
   Flat Bottom
   Cone Bottom
   Rectangular
   Tank & Mixer
   Shipping Drums
   Acid Neutralization
 
Reference
Catalog
Tank Safety Checklist
Specifications Manual
Installation Guide
Capacity Estimator
 
Extended Tank Warranty / Expediting Service
 Contact Sales for Info
 



Tank & Mixer Packages
Pre-Engineered - Ready to Use

Chem-Tainer's tank and mixer packages are designed, engineered and
built to provide long, trouble free service in blending and mixing applications.  
Our pre-engineered packages are used to blend liquids, suspend or dissolve
solids, and dispense immiscible liquids in a wide variety of industrial
applications.  Blend and mix paints, varnishes, polymers, textile sizes
and dyes, pharmaceuticals and countless other materials from 1 to 2,000
CPS viscosity.
Click here view tank installation and use guidelines.

NEPTUNE MIXER FEATURES:
CTBN 10 & 20 Models
Coupling fully enclosed for safety.  Direct drive-small batch mixing.  316 Stainless Steel shafts and propellers.  Clamp adjusts to any angle.

CTJG 20, 30, 40 & 50 Models - 350 RPM gear-driven.  316 Stainless Steel shafts and propellers.  1.0 pitch ratio marine propellers.  Flow co-efficient and power consumption characteristics equal to those of the best hydro foil impeller designs.  Adjustable shaft angle to achieve optimum mixing for various processing needs.  Motors are enclosed, fan cooled (TEFC).  Explosion-proof motor available.  Permanent grease gears.  Mixer shaft bearings are permanently lubricated.  Available with air motors for use in flammable, or explosion-proof environments.

Mixer Selection Chart

Our chart is intended to furnish basic guidelines for selecting the proper mixer to provide a mild blending of liquids of various viscosities in different size tanks.  This information is based on an approximate 30 minute mix-blend time for two liquids when both liquids are already in the tank.  Mixing times can be shortened if one liquid is added while the first liquid is already being mixed.   Powders should always be added while mixer is running.

VISCOSITY
CPS
TANKS UP
TO
50 GAL
TANKS UP
TO
100 GAL
TANKS UP
TO
200 GAL
TANKS UP
TO
500 GAL
TANKS UP
TO
1,000 GAL
  Mixer Part # Mixer Part # Mixer Part # Mixer Part # Mixer Part #
< 1 CTBN10 CTBN10 CTBN10 CTBN10 CTJG10 Where To Buy
< 100 CTBN10 CTBN10 CTBN20 CTJG10 CTJG10 Where To Buy
< 300 CTBN10 CTBN20 CTJG10 CTJG10 CTJG20 Where To Buy
< 500 CTBN20 CTJG10 CTJG10 CTJG10 CTJG30 Where To Buy
< 1000 CTBN20 CTJG10 CTJG20 CTJG20 CTJG40 Where To Buy

Optimum mixing will be achieved when the mixer is angled from the tank wall.  "Angling-Off" center is preferred when good material turnover is required, as in mixing a slurry.  "Angling-On" center is desirable for a gentle mixing action or when vortexing must be minimized.  Improper mounting of a mixer can greatly lessen mixing efficiency, cause vibration, and possible damage the mixer.

 
Customer Service | About Us | Help
Copyright © 2014 Chem-Tainer Industries

Email: sales@chemtainer.com
Other Chem-tainer Sites: